Help with AH5 Model 1 for Xbox 360 coin acceptor set example

Questions about our products

Help with AH5 Model 1 for Xbox 360 coin acceptor set example

Postby fatreap70 » Wed Apr 09, 2008 5:17 pm

I have a few questions setting this up

1. Can I set the AC5 for $1 US coins?

2. There are 4 USB plug ins in the box. What plugs into them? Which one plugs into the Xbox 360 console and which ones are for the controllers? Does it matter?
fatreap70
 
Posts: 8
Joined: Wed Apr 09, 2008 5:12 pm

Re: Help with Model 1 for Xbox 360

Postby Administrator » Wed Apr 09, 2008 7:33 pm

1. Yes, you can setup AC5 for $1 US coin, just let it output 4 times pulse value that Quarter does.
2. 4 USB plugs, 1 and 2 is a set for player 1, 3 and 4 is a set for player 2 or wise verse.
you can connect 1 to XBox 360 , 2 to XBox 360 controller, or you can connect 2 to XBox 360 , 1 to XBox 360 controller.
Seam for seconds controller.
Administrator
 
Posts: 386
Joined: Tue Jan 16, 2007 1:38 am

Re: Help with Model 1 for Xbox 360

Postby fatreap70 » Wed Apr 09, 2008 10:18 pm

Thanks for the answer. I assume the ports are from top to bottom. If that's wrong, please correct me.

I got the coin part working and I will explain in detail how I did it for those who may need help.

1. Plug in and wait at least 10 minutes before programming. This seems to be very important.

2. First, you must erase the current settings. To do that do the following 3 steps.
1. Turn the sensitive switch to the NOM position.
2. Turn the setting switch to the SET position. The LED will display 00.
3. Press and hold the coin adjust switch until C is displayed. The current setting are now erased.

3. Verify the following 4 switch settings and set if necessary.
1. Turn the open/close switch to NO position.
2, Turn the time switch to the FAST position.
3. Turn the sensitve switch to the NOM position.
4. Turn the setting switch to the SET postion.

4. Press the coin adjust switch once and 01 should be displayed.

5. Drop in 10 of your smallest valued coin. After 10 drops, an F will be on the display. This is your base value setting. All other settings will be based on this setting.

6. For your next valued coin, multiply the value of your base coin value X the number on the display = next coin value. For example, see the chart below for more detail.

Base Value = 5 cents, dime = 02 display setting, quarter = 05 display setting, dollar coin = 20 display setting.

7. After you do this for all your coins, turn the sensitive switch to MGN.

8. Now you want to set up your credit value setting. You do this by pressing the coin adjust switch to the right LED number. Using the example above for the base coin value setting as 5 cents, 01 gives you credit for 5 cents, 02 gives you credit for 10 cents, 03 = 15 cents, 05 = 25 cents, 20 = $1.00, you get the point. With my setup, I did have to go all the way to 99, then back to 01 to get it to work. You may need to do this.

9. Turn the setting switch to START and you should be good to go.
fatreap70
 
Posts: 8
Joined: Wed Apr 09, 2008 5:12 pm

Re: Help with Model 1 for Xbox 360 coin acceptor setup

Postby Administrator » Thu Apr 10, 2008 3:15 am

All the steps are correct and clear. Thank for sharing.
Thanks your so much for your detailed step by step setup for the coin acceptor.
It is very helpful for other users, we may include your step by step in our manual if you do not mind. :)
Here is the manual for the setup in case it is not supplied.

1. To erase all previous coin values setting
• Turn the Sensitive switch to the “NOM” position
• Turn the setting switch to the “SET” position to enter the programming mode, the LED will display “00”
• Keep pressing the Adjust Setting Switch for 5 seconds or more until you hear a “Beep” sound. The LED should display “C”, to indicate that the previous coin values were cleared.
• Turn the setting switch to the “START” position to exit the programming mode
2. To erase the previous one specified type coin value setting
NOTICE: This setting was meant for advance users only
• Turn the Sensitive switch to the “NOM” position
• Turn the setting switch to the “SET” position to enter the programming mode, the LED will display “00”.
• The Adjust Setting Switch will increase the coin value by each press. Keep press the button until the desired setting is reached. (For example, if coin Quarter value is 2, the let the LED display “02”)
• Press and hold the Adjust Setting Switch for 5 seconds or more until hear a “Beep” sound. The LED will display “C”, to indicate that the previous coin value was cleared.
• Turn the setting switch to the “START” position to exit the programming mode.
3. To set coin values
• Turn the Sensitive switch to the “NOM” position
• Turn the Setting Switch to the “SET” position to enter the programming mode, the LED will display previous setting, for example “01”
• Press the Adjust Setting Switch to adjust the coin value in turn and let the LED display the desirable value, for example “01” or “02”. The value increase 1 upon 1 press. If the desirable value passed, just turn the setting switch to “START” then turn back to “SET” again the LED will display “00”, the value can be selected again.
• Deposit the coins in turn, can program up to 10 coins .If less than 10 coins can add and store later. For example can prepare 10 quarters as different condition as possible. Or can deposit 10 same or different tokens.
• Repeat above two steps to set other coin values.
• Turn the setting switch to the “START” position to exit programming mode
• For example if the Quarter is set coin value as 02 means 1 quarter output 2 pulses.
4. To erase the previous coin minimum start value setting
• Turn the Sensitive switch to the “MGN” position
• Turn the setting switch to the “SET” position to enter the programming mode, the LED will display previous setting, for example default value “01”
• Press and hold the Adjust Setting Switch for 5 seconds until hear a “Beep” sound and LED will display “C” , to indicate that the previous coin values were reset to “01”
• Turn the Sensitive switch to the “NOM” position
• Turn the setting switch to the “START” position to exit the programming mode.
5. To set coin minimum start value values
(this value means only when all the dropped coins’ values accumulate to or greater than the minimum start value, the AC5 can start to output pulse signal)
• Turn the Sensitive switch to the “MGN” position
• Turn the Setting Switch to the “SET” position to enter the programming mode, the LED will display previous setting, for example “01”
• Press the Adjust Setting Switch to adjust the coin value in turn and let the LED display the desirable value, for example “01” or “02”. The value increase 1 upon 1 press. If the desirable value passed, just turn the setting switch to “START” then turn back to “SET” again the LED will display pervious setting, the value can be selected again.
• Turn the setting switch to the “START” position to exit programming mode
For example: if the Quarter is set coin value as 02 means only 2 quarter output 1 pulse, drop 1 quarter, the AC5 does not output pulse.
Example B: Setup for Canadian Nickel (0.05), Dime (0.10), Quarter (0.25), Loony ($1.00), and Toony ($2.00) output pulse only up to 0.25.
1. Clear all the settings. Following above step 1, 2 and 4 to erase previous settings.
2. Prepare 10 Nickels, 10 Dimes, 10 Canadian Quarters, 10 Loonies, and 10 Toonies.
3. Turn the Sensitive switch to NOM
4. Turn the Setting Switch to SET going to Programming mode, LED will show “00”
5. Press Adjust Setting Switch once, the display will show “01”, drop the 10 nickels in sequence, when drop the 10th nickel, LED will show “F” means the setting is done.( if pressed more times, for example LED show “01” or “02”, first turn the Setting Switch to START, then turn Setting Switch to SET again the display will show “00”)
6. Press Adjust Setting Switch once, LED will show “02”, drop the 10 dimes in sequence, when drop the 10th dime, LED will show “F” means the setting is done
7. Press Adjust Setting Switch 3 time, LED will show “05”, drop the 10 quarters in sequence, when drop the 10th quarter, LED will show “F” means the setting is done
8. Press Adjust Setting Switch 15 times until LED show “20”, drop the 10 Loonies in sequence, when drop the 10th quarter, LED will show “F” means the setting is done.
9. Press Adjust Setting Switch 20 times until LED show “40”, drop the 10 Toonies in sequence, when drop the 10th quarter, the LED will show “F” means the setting is done.
10. Turn the Sensitive switch to MGN
11. Press Adjust Setting Switch 5 times until LED show “05”
12. Turn Setting Switch to START, then AC5 is ready to use.
13. When drop 1 quarter, it will output one pulse signal, drop 1 Loony it will output 4 pulse signal, drop 1 Toony it will output 8 pulse signal, and only when drop 5 nickels = 1 dime and 3 nickels = 2 dimes and 1 nickels >= 0.25 then it will output 1 pulse signal.. When drop 1 quarter, it will output one pulse signal, drop 1 quarter it will output 8 pulse signals
Example D: Setup for US$ Nickel (0.05), Dime (0.10), Quarter (0.25), output 1 pulse only up to 0.25.
1. Clear all the settings. Following above steps 1 and 3 to erase previous settings.
2. Prepare 10 Nickels, 10 Dimes, 10 Canadian Quarters, 10 Loonies, and 10 Toonies.
3. Turn the Sensitive switch to NOM
4. Turn the Setting Switch to SET entering Programming mode, LED will show “00”
5. Press Adjust Setting Switch once, LED will show “01”, drop the 10 nickels in sequence, when drop the 10th nickel, LED will show “F” means the setting is done.( if pressed more times, for example LED show “01” or “02”, first turn the Setting Switch to START, then turn Setting Switch to SET again LED will show “00”.)
6. Press Adjust Setting Switch once, LED will show “02”, drop the 10 dimes in sequence, when drop the 10th dime, LED will show “F” means the setting is done
7. Press Adjust Setting Switch 3 times, LED will show “05”, drop the 10 quarters in sequence, when drop the 10th quarter, LED will show “F” means the setting is done
8. Turn the Sensitive switch to MGN
9. Press Adjust Setting Switch 5 times until the display show “05”
10. Turn Setting Switch to START, then AC5 is ready to use.
11. When drop 1 quarter, it will output one pulse signal, and only when drop 5 nickels = 1 dime and 3 nickels = 2 dimes and 1 nickels >= 0.25 then it will output 1 pulse signal.
Example E: Setup for drop 4 Quarter (0.25), output 1 pulse
1. Clear all the settings. Following steps above 1 and 3 to erase previous settings.
2. Prepare 10 Quarters
3. Turn the Sensitive switch to NOM
4. Turn the Setting Switch to SET entering Programming mode, LED will show “00”
5. Press Adjust Setting Switch 1 time, LED will show “01”, drop the 10 quarters in sequence, when drop the 10th quarter, LED will show “F” means the setting is done
6. Turn the Sensitive switch to MGN
7. Press Adjust Setting Switch 4 times until the display show “04”
8. Turn Setting Switch to START, then AC5 is ready to use.
9. Only when user drop 4 quarters, the AC5 will output one pulse signal,
Administrator
 
Posts: 386
Joined: Tue Jan 16, 2007 1:38 am


Return to Do you need help?

Who is online

Users browsing this forum: No registered users and 2 guests

cron